Introduction:
This
tool is designed for accurate parking. if you have a problem with the
appraisals, how far is the automobile from the wall when the park, you can use
this device to avoid collision. the ultrasonic technology, which works
automatically. let you know the sound and the three led lights. is a 9v battery
(6f22) or an external source that provides a dc voltage of 9v. it consists of a
display unit, a sensor unit and a cable. it also has low battery indication.
Appearance:
1. ultrasonic hole
2. the
switch
3. the
input jack (external power supply)
4. red
ice
5. the
yellow led
6. the
green ice
7. the
hummer
Installation:
According to figures 2 and 3 include
imaging and sensor unit on the wall. the imaging unit should be attached so
that her driver knew. the sensor unit is mounted directly below the display,
typically 0.7 to 0.9 metres above the ground. Different vehicles may lower the sensor
unit at different locations. a small adjustment may be necessary.
Make sure it's an ultrasonic aperture at
the same level as the bumper or the license plate to the ultrasound reflected
back to the sensor unit.
After the completion of the installation,
try parking your car using the apparatus to make sure that it is installed
correctly.
Note:
1. the cable should
be firmly connected to the sensor and a display unit.
2. make sure that a
sensor unit is no obstacle, which could get in the way of ultrasound.
Picture 2 Picture 3
ultrasonic aperture is at the same
height as a buffer the imaging unit should be
attached t to the driver can see
or license plate
The operating instructions
1.
turn on the machine.
3.
when the distance between the sensor unit and the car between 0.4 m and about 5
m:
a. And on ice and apparatus make a sound when the
automobile approaches the unit.
Note:
the frequency of the alarm buzzer is constant, the distance between the car and
the sensor unit less than approximately 0.5 m. if the distance between
approximately 0.5 m and about 5 m, the frequency of the alarm buzzer varies
with distance. the shorter the distance, the higher the frequency of the alarm
buzzer.
b.
the buzzer will issue a beep, and then shuts down when the car stops to move
toward the sensor unit or when the automobile stops to move to the sensor unit
and begins to move away from her.
c.
the machine lights up ice and turns off the sound when the automobile is moving
from the sensor unit.
d.
the apparatus off ice for approximately 20 seconds after the automobile is
parked.
4.
the machine stops any indication about after 20 seconds, if the distance
between the vehicle and the sensor unit is less than 0.4 m. if the car is
moving from the sensor units and is about 0.4 m far away from her, the buzzer
will issue a beep, and then shuts down.
Notes:
1. the machine can work continuously and
automatically. if it is not long time to use, remove the battery or the
external power supply.
2. when you use the machine, make sure there are no sources in the
vicinity of the ultrasound.
3. use the device only in dry and clean the garage, in which there is no
draft.
4. do not open the machine before the machine off. to prevent electric
shock.
5. if entering the garage the car is going too fast, it may reduce the accuracy.
6. do not use the appliance when the casing is disconnected or the
battery or part of the housing.
7. do not use the apparatus in the vicinity of explosive gases, vapours
or dust.
8. the maximum detection capacity of the apparatus is 5 meters.
The exchange of the battery:
If the buzzer to sound and three led flashing
at the same time, you should immediately to replace the battery. Before the exchange battery device
turn off and unplug the external power supply.
Remove the
batteries and the rear side of the sensor unit, replace a dead battery in a
same type.
Battery back cover
back.
The basic
specifications:
Low battery
indication: the three led at the same time, buzzer and flashing.
Power: 9v battery
(6f22 or equivalent) or an external source two 9v.
Working
temperature: 32 today when 50°c, air humidity < 75%.
Storage
temperature: - 50 degrees to 135, air humidity < 85%.
Size: display: 185
x 61 x 31 mm.
The sensor unit: 82
x 61 x 37 mm. weight: approximately 180 g (without battery)
Notes:
1. the content of
this manual may be changed without notice.
2. the manufacturer
does not assume responsibility for any loss.
3. the contents of
this manual may be used j
Park Indicator Park Indicator,Park Sensor,Sensor Parking,Parking Sensors Shenzhen Cartrend Technology Co, Ltd , https://www.cartrendthings.com
Large newspaper Waste magazine grinder
Machine for chopping or grinding, cutting and shredding of PET and other plastic materials such as polypropylene PP, polyethylene PE, PES polyester, polystyrene PS, EVA, PVC, HIPS, big-bags, thermal blanket, plastic greenhouse, plastic agriculture raffia nets, ropesÂ
XINHANG offers the cutting and shredding ROTATOR, a machine with working widths of 400-1500MM, with a variable cutting length (due to speed setting the feed belt) and a production capacity of up to 8000kg / hour (depending on the size of the shredded material).
The cutting process begins with the advance of the conveyor belt variable speed (adjustment of the cutting length is easily accomplished from the control panel). Subsequently, they pass the rotary cutting system, consisting of several blades. Finally, the extraction weaver totally evacuates all shredded matter.
Depending on the capacity of cutting or shredding or shaped material feeding for processing that is required, XINHANG offers several models ROTATOR shredder.
Remarks;
Delivery time; 10-30days after receiving clients prepayment;
Payment term; 50% as prepayment by T&T; the balance of 50% should be paid before seller send the machine;
Â
Valid time; This quotation is valid for one month;
Â
Quality Guarantee Terms;
Quality guarantee term is for one year; Malfunctions which are caused by machine-self and quality will be responsible for our manufacturer; Other malfunctions which are caused by operation mistakes,man-made problems and etc will be responsible for clients-self;
Product service:
1.keep the quality the first .
2.technology knowledge shareÂ
3.make more products benefit to customer's requirment.
After-sale service :
1.repairing and maintenance if any problem accur in the warranty ,
2. assistance to bulit factory or your projectÂ
3.spare and wearning parts for free or with big discount.
4.any feedback of machines can be told us , and we will try our best to support you .
Other service :
1. our staffs will solve your problem at any time .
2.after receiving the email , we will answer to you within 24 hours .
FAQ
1.Is your company a trading one or a factory?
Factory and trade (we have our own factory site.)
2,Which payment terms are you accepted?
T/T, Paypal and Western Union.
3.When to deliver the goods after the order is placed?
It depends on the quantity of the products. Generally we can arrange shipment after 7 to 15 days.
4. Does your company accept customization?
We have excellent design team, and we accept OEM.
5.What about the cooperation process?
Confirm details of the order, 30% deposit, arrange to produce, pay the balance before shipment..
Â
3. an ultrasonic aperture should be at the same height as a buffer or a
plate.
2. the three led is lit
under the conditions of figure 4. the horizontal axis indicates the distance
between the sensor unit and the car. the sensor unit is in position zero.
Large Newspaper Waste Magazine Grinder