The arrival of winter has caused some industries to start anti-freezing measures. For the anti-freezing of electric vehicle batteries , most people do not take it seriously. In fact, it is important to pay attention to the anti-freezing of electric vehicle batteries, which is also difficult to repair and even scrap. the reason. Therefore, in the winter, we should pay attention to anti-freezing measures for the battery, electric vehicle era network Xiaobian prompts the owners, battery antifreeze can start from the following aspects:

1. Greenhouse overhead storage: In order to prevent the battery from being frozen, the electric vehicle battery should be stored in the house above 0 °C when not in use, and should not be placed directly on the ground. Before storing, clean the exterior of the battery of the electric vehicle, add enough electrolyte, fully charge the battery, and tighten the screw plug.

2. Increasing the electrolysis temperature: The temperature of the electrolyte has a great influence on the capacity of the electric vehicle battery. For every 1 °C decrease in the ambient temperature, the capacity is reduced by about 1% to 2%. To this end, to increase the temperature of the electrolyte, the electric vehicle should be parked indoors, or the battery should be moved into the room above 0 °C.

3, water and liquid mixing evenly: electric vehicle battery added distilled water should be mixed with the electrolyte evenly. If it is too late to mix, the distilled water floating on the upper layer of the electrolyte will freeze. To add distilled water to the electric vehicle battery in the winter, it should be charged immediately, or distilled water can be added while charging, so that the electrolyte and distilled water can be quickly mixed, and it will not freeze.

4. Increasing the liquid ratio: The electrolyte consists of water and sulfuric acid. The higher the content of sulfuric acid in the electrolyte, the higher the specific gravity of the electrolyte and the lower the temperature of the electrolyte. To this end, localities can choose the appropriate electrolyte specific gravity according to the local minimum temperature in winter to prevent the electrolyte from freezing. Once the electrolyte is iced, it will cause the battery to be scrapped.

5, to maintain the state of full power: in the winter when the electric vehicle battery discharge 50%, the electrolyte has the danger of freezing. For this reason, the discharge level of the electric vehicle battery in winter is not allowed to exceed 50%. In the winter, it is necessary to check the storage condition of the electric vehicle battery frequently. If it is insufficient, it should be replenished in time. Ensuring the storage capacity of the electric vehicle battery is to effectively protect the battery.

Pipe fittings

Excavator pipe fittings and tube fittings are essential components in the hydraulic system of excavators. These fittings are used to connect hydraulic hoses and tubes to various components of the excavator, such as the hydraulic pump, cylinders, and valves.

There are various types of excavator pipe fittings and tube fittings, including:

1. Flanges: Flanges are used to connect two pipes or tubes together. They are usually bolted together and provide a leak-free seal.

2. Adapters: Adapters are used to connect two different types of fittings or components. They can be male or female, and can be used to connect hoses, tubes, or other components.

3. Elbows: Elbows are used to change the direction of a pipe or tube. They come in various angles, such as 45 degrees or 90 degrees.

4. Tees: Tees are used to connect three pipes or tubes together. They come in various configurations, such as equal tees or reducing tees.

5. Couplings: Couplings are used to connect two pipes or tubes together. They can be either rigid or flexible, and are often used in tight spaces where movement is limited.

Excavator pipe fittings and tube fittings are made from various materials, including steel, brass, and aluminum. The choice of material depends on the application and the environment in which the excavator is used. For example, steel fittings are often used in high-pressure applications, while brass fittings are used in low-pressure applications.

Overall, excavator pipe fittings and tube fittings are critical components in the hydraulic system of excavators. They ensure that hydraulic fluid flows smoothly and efficiently through the system, enabling the excavator to perform its tasks effectively.

Pipe Fittings ,Hydraulic Plumbing Fitting,Hydraulic Pipe Fitting,Hydraulic Tube Fitting

CATSU Hydraulic Machinery Equipment Co.,Ltd , https://www.catsutiltrotator.com