Smart Parking System,Hydraulic Automatic Parking System,Stacker Car Parking System Suzhou Tailing Elevator Co.,ltd , http://www.sztl-elevator.com
Characteristics:
This valve is applicable for discharge and transportation of dry ash systems in power plants and storehouse pumps, or can be used as an on-off device for pipelines containing abrasive dry ash, water (such as cinder water ) and the like in mines, paper making, chemical engineering and so on, as an on-off for pipelines with both soft grains and corrosive media. Its working nominal pressure is 1.0MPa, applicable temperature is below 200 Deg C, and air supply pressure is 0.6-0.8MPa.
After the valve closed, it's fully sealed in any direction. Its middle body adopts WCB steel casting and seamless steel pipe welding. Its sealing surface adopts a hard sealing element.
Its feed inlet is fully through without any blocks, and it has an automatic compressed air anti-blcikage blowing unit, with strong abrasion resistance, a good sealability, a small starting load and with  little ash sezure of accumulation.
It adopts a high-grade toughened structural ceramic seal, featuring high mechanical strength, strong abrasion resistance, a long service life and a compact structure, which can be installed at any angle.
Special ceramics is different from general ceramics, its hardness even more than steel,
second only to diamond, and corrosion resistant, high temperature resistant!!!!! "" metal
valve with long easy to produce the gap, ceramic valve is not. Because of wear-resisting,
anti-corrosive, sealing strong, ceramic water valve very water saving. "" our valves can be
used 500000 times, if every switch 60 times, can use 22.8 years, this is metal valve can not do it. "
Main Parts and Materials
Sr No.Parts
Material
Sr No.
Parts
Material
1
Body
WCB
7
Middle Body
WCB
2
Disc
Ceramic
8
Packing
Flexible Graphite
3
Seat
Ceramic
9
Packing Gland
2Cr13
4
Stem
2Cr13
10
Bracket
Q235
5
Stud
35CrMoVA
11
Pneumatic Actuator
Aluminum Body
6
Nut
25
Â
Â
Â
Application Specification
1. Design and Manufacture: GB/T 12224
2. Face to Face Dimension: Manufacturer's Standard
3. Flange Dimension: JB/T 79.1, ANSI B16.5 Â DIN 2543, JIS B2020
4. Inspection and Test: GB/T 9092
5. Material Standard: GB/T 12229 for Carbon Steel, GB/T 12230 for Stainless Steel
Main External and connecting Dimensions
DN
PN
L
D
D1
H
n-d
50
10
120
160
125
280
4-16
65
120
180
145
295
4-16
80
120
195
160
320
8-16
100
120
215
180
380
8-16
125
160
245
210
400
8-16
150
160
280
240
480
8-20
175
160
310
270
600
8-20
200
160
335
295
800
8-20
250
20
405
350
1250
12-22
300
20
460
400
1550
12-22
Â
Pneumatic Ceramic Feed Valve(GZD644TC)
Characteristics:
This valve is applicable for discharge and transportation of dry ash systems in power plants and storehouse pumps, or can be used as an on-off device for pipelines containing abrasive dry ash, water (such as cinder water ) and the like in mines, paper making, chemical engineering and so on, as an on-off for pipelines with both soft grains and corrosive media. Its working nominal pressure is 1.0MPa, applicable temperature is below 200 Deg C, and air supply pressure is 0.6-0.8MPa.
After the valve closed, it's fully sealed in any direction. Its middle body adopts WCB steel casting and seamless steel pipe welding. Its sealing surface adopts a hard sealing element.
Its feed inlet is fully through without any blocks, and it has an automatic compressed air anti-blcikage blowing unit, with strong abrasion resistance, a good sealability, a small starting load and with  little ash sezure of accumulation.
It adopts a high-grade toughened structural ceramic seal, featuring high mechanical strength, strong abrasion resistance, a long service life and a compact structure, which can be installed at any angle.
Special ceramics is different from general ceramics, its hardness even more than steel,
second only to diamond, and corrosion resistant, high temperature resistant!!!!! "" metal
valve with long easy to produce the gap, ceramic valve is not. Because of wear-resisting,
anti-corrosive, sealing strong, ceramic water valve very water saving. "" our valves can be
used 500000 times, if every switch 60 times, can use 22.8 years, this is metal valve can not do it. "
Main Parts and Materials
Sr No.Parts
Material
Sr No.
Parts
Material
1
Body
WCB
7
Middle Body
WCB
2
Disc
Ceramic
8
Packing
Flexible Graphite
3
Seat
Ceramic
9
Packing Gland
2Cr13
4
Stem
2Cr13
10
Bracket
Q235
5
Stud
35CrMoVA
11
Pneumatic Actuator
Aluminum Body
6
Nut
25
Â
Â
Â
Application Specification
1. Design and Manufacture: GB/T 12224
2. Face to Face Dimension: Manufacturer's Standard
3. Flange Dimension: JB/T 79.1, ANSI B16.5 Â DIN 2543, JIS B2020
4. Inspection and Test: GB/T 9092
5. Material Standard: GB/T 12229 for Carbon Steel, GB/T 12230 for Stainless Steel
Main External and connecting Dimensions
DN
PN
L
D
D1
H
n-d
50
10
120
160
125
280
4-16
65
120
180
145
295
4-16
80
120
195
160
320
8-16
100
120
215
180
380
8-16
125
160
245
210
400
8-16
150
160
280
240
480
8-20
175
160
310
270
600
8-20
200
160
335
295
800
8-20
250
20
405
350
1250
12-22
300
20
460
400
1550
12-22
Â
More efficency for car park in and out. more parking port and safety protection
Suzhou Tailing Elevator Co.,Ltd has been registered in Wujiang,Suzhou,China and established in 1998.It is a hightech elevator manufacture which integrate the manufacture,sales,installation,repair,maintenance,transformation into one.
At present,the company has 40,000 square meters of factory zones including 26,000 square meters of the manufacture area. .Meanwhile it invest in 125million RMB to build up over 40,000 square meters of new factory workshop.The total area reach above 80,000
Square meters.It currently has more than 500 employees. Among them,the engineering technical share 70%.It has more than 30 person in R&D .
The company applyA full set of the advanced Mitsubishi Inazawa technology and the scientific mode of management. Therefore the product stably share more and more domestic markets.The company also sell the products to Pakistan,Iran,Africa,Ukraine,Egypt,etc. It becomes one of the elevator and escalator manufacturers with the best developing potentials in China
The company introduced the advanced Mitsubushi Inazawa technology,It is specailly engaged in designing,R&D and manufacturing passenger elevator,panorama elevator,machine roomless elevator,hospital elevator,goods elevator,villa elevator,escalator and moving walk.And we have successfully research and developed the world leading Three-In-One steel belt elevators and advanced Lift-sliding mechanical parking system,Vertical lifting mechanical parking system
Suzhou Tailing Elevator Co.,Ltd have passed ISO9001:2008 Quality System Certification.ISO14001:2004 Enviromental Management System Certification, and 280012011 idt OHSAS 18001:2007 GB/T Occupational Health and Safety Management System Certification.It firstly introducs the quality supervision system into the elevator industry.It lays a solid foundation to increasing the product quality.Nowday the company has been ability with annual productive capacity of 15,000 sets of elevators and escalators.The products are well-received by vast nation-wide clients because of the perfect after-sale service networks and the after-sale severice concept of customer firstly. It has fulfilled moden business standards in the aspects of the production resources and business management.The company accords with the idea of"safe,reliable,superior,superior,effective"to continuously get the general approval and deep trust from extensive customer.
Suzhou Tailing Elevator develop prosperously by the dedicatory spririts of"green environmental protection,be bent on forging ahead".It is an effective,uinted and uprising team.It is sure to creat miracle in the chinese elevator industry.Suzhou Tailing Elevator will always adhere to the sincere,pragmatic and enthusiatic attitudes to continuously serve vast domestic and overseas users.
Pneumatic Ceramic Feeding Valve (GZJ644TC)
Model NO.: GZJ644TC
Thread Position of Valve Rod: Outside Gate Valve
Usage: Emptying
Standard: DIN
Application: Industrial Usage
Suitable Temperature: Below 200 Deg C
Size: Dn50-Dn400
Medium: Dry Ash in Power Plant, Slurry, Cement Ash, Powder
Design Pressure: Pn10, Pn16
Connection: Flanged
Air Supply Pressure: 0.6-0.8 MPa
Trademark: GOOLE, OEM
Transport Package: Plywood Case
Specification: CE, SGS, GMP
Origin: Wenzhou, Zhejiang, China
HS Code: 8481804090
Model NO.: GZJ644TC
Thread Position of Valve Rod: Outside Gate Valve
Usage: Emptying
Standard: DIN
Application: Industrial Usage
Suitable Temperature: Below 200 Deg C
Size: Dn50-Dn400
Medium: Dry Ash in Power Plant, Slurry, Cement Ash, Powder
Design Pressure: Pn10, Pn16
Connection: Flanged
Air Supply Pressure: 0.6-0.8 MPa
Trademark: GOOLE, OEM
Transport Package: Plywood Case
Specification: CE, SGS, GMP
Origin: Wenzhou, Zhejiang, China
HS Code: 8481804090
Pneumatic Ceramic Feed Valve(GZD644TC)