CD printer uv printing machine
is suitable for producing different patterns which contain relief,
hollow out, flat print on different material. It is widely used on
glass, wooden board, metal board, ceramic, leather, PVC, acrylic etc. It
makes products value higher.
Advantge:
1. With Instant print & instant dry, it is no need pre-coating, UV proof, water proof, scratch proof, which is superior
2. With Easy operation & simple production. No matter printing a simple block color pattern, printing full-color pattern or a
CD Printer,Laser CD Printer,Digital CD Printer,Inkjet CD Printer,Mini CD Printer Shenzhen Refinecolor Technology Co., LTD. , https://www.sztshirtprinter.com
The steady flow stress also has the same change law. When the deformation temperature is further lowered, or the deformation rate is further increased, the deformed austenite changes from a fully dynamic recrystallization state to a partial dynamic recrystallization to a final work hardening state.
The microstructure of Mn-Cr gear steel at 950 °C and 1 s-1 deformation 016 is indicated under different original austenite grain sizes. When the grain size is 140 μm, the original austenite grains are significantly elongated in the direction perpendicular to the compression axis. At the same time, the prior austenite grain boundaries form many fine serrations. In some local regions, a very small amount of fine equiaxed recrystallized grains begin to form on the prior austenite grain boundaries, as shown in (b). The above experimental results show that the deformed austenite is basically in the critical state of recrystallization, and the critical strain is about 016. When the austenite grain is reduced to 100 μm, a large amount of recrystallized grains are formed, indicating deformed austenite. It is in a partially dynamic recrystallization state, and its structure is as shown in (c); when the crystal grain is reduced to 70 μm, the structure is completely composed of fine equiaxed grains, as shown in (d). This indicates that complete dynamic recrystallization has occurred. It can be seen that the original austenite grain size strongly affects the dynamic recrystallization behavior, and the fine grained austenite is prone to dynamic recrystallization and has a fast recrystallization kinetics. This is because when the fine austenite grains are deformed, the dislocation accumulation rate is fast, and the grain boundary area which can be used as the recrystallized nucleation site is large.
Stress-strain curves of Mn-Cr gear steel at different deformation temperatures and deformation rates In (b), grain boundary protrusions were observed at several locations in the prior austenite grain boundaries, as indicated by the arrows in the figure. Literature [2] pointed out that dynamic recrystallization of J crystals is nucleated by the prominent mechanism of austenite grain boundaries. In the early stages of the deformation process, local grain boundary shearing occurs frequently, causing the austenite grain boundaries to assume a sawtooth morphology. At the same time, a strain-induced subgrain boundary with medium and high angular mismatch is formed by dynamic recovery. During the grain boundary shearing process, the local strain gradient and the dislocation substructure are not uniform along the grain boundary. The local grain boundary is moved in a direction in which the dislocation density is high, that is, the grain boundary is protruded. At the same time, the strain-induced subgrain boundary with medium and high angular mismatch will act as a grain boundary to separate the protrusion from the parent. Thus, an independent recrystallized grain is formed on the prior austenite grain boundary.
to traditional screen printing.
gradient color pattern, engineer made the printer system can do in one procedure and it can also print mass production in one
template with different photos.
Name
CD printer
Print head
DX5
Printer size
33*43cm(33*60cm)
Printing speed
A4 photo/111s
Printng resolution
5760*1440dpi
Nozzles
90*6=540
Interface
USB2.0
Net weight/Gross weight
55Kg/60Kg
Printer size
750*630*510mm
Height adjustment
Automatic
Working power
110V/220V 50/60Hz 30-75W
Operation system
Windows 7/XP/2000/Vista etc
Temperature
5-35o
Manganese-chromium gear steel modal re-solidification operation and framework derivation