Vertical Single Slide Injection Molding Machine Vertical Injection Molding Machine Vertical Single Slide Injection Molding Machine,Vertical Plastic Moulding Machine,Small Vertical Injection Molding Machine,Vertical Plastic Injection Machine Ningbo Chenwei Machinery Technology Co.,Ltd , https://www.chenweimachinery.com
During the operation of the heavy wrecker, pay attention to the water temperature table, and the normal water temperature of the engine should be maintained between 80°C and 90°C. If it is too high or insufficient, the fuel consumption of heavy wreckers will increase. Special attention should be paid to the fact that if the wrecker tank water level is insufficient, the water temperature will quickly rise. If the water temperature exceeds 95°C, the wrecker's fuel consumption will increase by 30% to 40% compared with the normal temperature, and it will easily lead to clearing. The car's parts are worn and damaged. Regularly check the level of oil and lubricating oil on the road wrecker, and change the oil and lubricant according to the schedule. In addition, the correct maintenance of the wrecker engine, select the provisions of the brand of authentic oil, timely removal of wrecker car cylinder combustion chamber and the spark plug of the plot, found that the problem is ruled out at any time, even if it is a small fault, they will reduce the engine's power, waste of fuel . Regular replacement of air and oil filters will affect the fuel consumption of wreckers.
If you feel that the wrecker is not powered up, stop to see if there is a leak in the tire. If the tire pressure is too low, the fuel consumption will increase significantly. Keep the balance of the tires, check the tire's pattern from time to time to see if there is any uneven wear. At the same time to see if there is no sharp object embedded in the tire and cause a gradual leak. Always check the pressure of the wrecker tires to keep them in the best condition. Not enough gas or too much gas will increase fuel consumption. Therefore, tire pressure should be checked regularly. As long as there is one tire less 4kPa, this tire will reduce the life of 10,000km, and will increase the total fuel consumption of heavy wrecker.
Some of the above-mentioned heavy-duty wrecker fuel-saving techniques are based on years of experience gained by the Xiagong Chusheng Wrecker Factory. It is not denied that there are other ways to reduce fuel consumption, which is not explained here.
1. Each plastic cavity can be taken out by a simple manipulator, which is conducive to precision molding.
2. In small batch trial production, the mold structure is simple, low cost, and easy to unload.
3. It is easy to ensure the consistency of resin fluidity and mold temperature distribution in the mold.
4. After many earthquakes, the vertical machine has better seismic resistance than the horizontal machine due to its low center of gravity.
5. Equipped with rotating table, moving table and tilting table, it is easy to realize insert molding and in-mold combination molding.
6. The belt conveyor is easy to be installed in the middle of the mold, so as to realize the automatic production of molding.
7. Generally, the mold locking device is open around, and it is easy to configure various automatic devices, which is suitable for automatic forming of complex and delicate products.
8. The weight of the mould is supported by the horizontal formwork for opening and closing up and down. The phenomenon that the formwork cannot be opened and closed due to the forward fall caused by the gravity of the mould similar to the horizontal machine will not occur. It is beneficial to maintain the accuracy of machinery and mold for durability.
9. It is easy to realize the molding of the insert. Because the mold surface is upward, it is easy to put the insert into the position. The lower template is fixed and the upper template is movable. If the belt conveyor is combined with the manipulator, it can easily realize the automatic insert molding.
10. The injection device and mold locking device are located on the same vertical centerline, and the mold is opened and closed in the up and down directions. Its floor area is only about half of that of the horizontal machine, so it is about twice as productive.
Xigong Chu Sheng Heavy-Duty Wrecker Fuel-Efficient Method
Due to its large dynamic performance, large operating radius, various performances of various parts and complexity, and the specialization of objects for obstacle rescue, heavy duty wreckers make it natural to consume large amounts of fuel. How to protect road wreckers with high horsepower? The premise of power to reduce fuel consumption is a problem that many wrecker users are eager to understand. Here we talk about some ways to reduce the fuel consumption of heavy wreckers.